
Service · Los Angeles
New Construction Pre-Wire
in Los Angeles
LA Techs pre-wires new custom homes across Los Angeles: Wi-Fi, TVs, audio, Lutron lighting control, motorized shades, cameras and the equipment room. Planned with your architect, roughed in on your builder's schedule, before insulation.
Building now? Get a call back
Tell us a little about the house and a real person from LA Techs will call you back. Or call us now.
Call 424.324.5509What we pre-wire
One low-voltage contractor for every technology scope in the house, so the architect, builder and electrician coordinate with one team.
Network and Wi-Fi
Cat6A to every access point, screen, desk and camera, home-run to one equipment room
TVs and media walls
Network, power and conduit at every screen location, including future ones
Whole-home audio
Speaker wire to every in-ceiling, in-wall and outdoor speaker zone
Lighting control
Keypad locations and control wiring for Lutron HomeWorks or RadioRA 3, coordinated with your electrician
Motorized shades
Power and control at every motorized window, with pockets in the ceiling detail
Cameras, entry and security
Cameras, door stations, gate, door contacts and motion sensors
Home theater and media rooms
Projector, screen, speaker and lighting runs designed with the room
Equipment room
Sized, powered and cooled for the rack, with conduit to every floor, the attic and the street
The full checklist, location by location, is the free LA Techs Pre-Wire Standard.
How a pre-wire runs
Step 1
Plan review
Send us the plans. We mark up device locations, size the equipment room and give you a budget range by system.
Step 2
Low-voltage drawings
A low-voltage sheet coordinated with the electrical plan, keypad elevations, shade pocket details and specs for the set.
Step 3
Pre-wire
After framing, before insulation. We rough in to the drawings on the GC's schedule, then walk the house with the owner and designer and photograph every wall.
Step 4
Trim, programming, support
After paint we install, program and hand over with documentation and a 90-day warranty. Support plans are optional.
What the design team gets at each phase: New Construction. For architects and builders: how we work with your team.
Why builders and architects call us
- Licensed low-voltage contractor: CSLB #1031050 (C-7 low voltage and C-10 electrical)
- CEDIA member; authorized Control4, Savant and Lutron dealer
- In Los Angeles since 2006
- One point of contact for lighting, shades, audio, video, network and security
- Documented pre-wire: wall photos before insulation, every cable labeled at both ends
- 90-day warranty on every installation, with support plans after move-in
Where we pre-wire
Custom homes and rebuilds across greater Los Angeles, from our base at 15500 Erwin St, Suite 1017, Van Nuys, CA 91411. Rebuilding after the fires? See Palisades and Malibu rebuilds.
Common questions
Who does smart home pre-wire for new custom homes in Los Angeles?
LA Techs pre-wires new custom homes across Los Angeles: network and Wi-Fi, TVs, whole-home audio, Lutron lighting control, motorized shades, cameras and the equipment room. We are a licensed low-voltage contractor (CSLB #1031050, C-7 and C-10), a CEDIA member and an authorized Control4, Savant and Lutron dealer, in business since 2006. New projects: 424.324.5509.
When should pre-wire happen on a new build?
After framing and before insulation. The planning should happen much earlier, during design, so device locations, shade pockets and the equipment room are on the drawings before anyone frames a wall.
What does a smart home pre-wire include?
Cat6A to every access point, screen, desk and camera; speaker wire to every speaker; control wiring to every lighting keypad; power and control at every motorized shade; camera, entry and security wiring; a dedicated equipment room; and spare conduit to every floor, the attic and the street.
Do you work with our architect, GC and electrician?
Yes, on every project. We draft the low-voltage sheet with the architect, hand the electrician a lighting control layout and load schedule, rough in on the GC's schedule and answer RFIs. One person at LA Techs is your point of contact.
Do you pre-wire Palisades and Malibu fire rebuilds?
Yes. A rebuild is the best chance to get the technology right while the walls are open. See our rebuild page for how we work with families, architects and builders there.
How much does pre-wire cost?
It depends on the size of the house and the systems in it. We give a budget range broken out by system once we see the plans, so the team can decide what to keep before anything is drawn in detail.
Have plans? We'll mark them up.
Send the set and we'll come back with device locations, the equipment room and a budget range by system.